Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

Sheet Metal Worker Exam Illustrated: Every Pattern Drawn, in the Same Steps Every Time One Fitting on Every Page

For the Red Seal Sheet Metal Worker exam, written for Canada: metric, with imperial where the shop still uses it. Gore angles, stretchouts, square-to-rounds, the Pittsburgh lock, the fan laws, dampers, hangers and flashing, each on its own page: the drawing first, then what you need to remember. 66 illustrated pages.

START STUDYING THIS WAY

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEvery pattern drawn step by step, with the explanation beside it
66 illustrated pages9 parts, from how the exam is built to the last two weeks before it
Up-to-date sourcesRed Seal Occupational Standard, National Building Code of Canada and CSA standards
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the steps and numbers you need to know:

Equivalent round of 400 × 300 mm ≈ 378 mm (equal area would be 391 mm).
Equivalent round of 400 × 300 mm ≈ 378 mm (equal area would be 391 mm).
Gore = angle ÷ (pieces − 1): 90° in 5 pieces = 3 × 22½° + 2 × 11¼°.
Gore = angle ÷ (pieces − 1): 90° in 5 pieces = 3 × 22½° + 2 × 11¼°.
Why an offset square-to-round needs a true length diagram for each quarter.
Why an offset square-to-round needs a true length diagram for each quarter.
Grease duct: 16 MSG steel or 18 MSG stainless, continuous liquid-tight welds, leak-tested.
Grease duct: 16 MSG steel or 18 MSG stainless, continuous liquid-tight welds, leak-tested.
+10% rpm → +10% flow, +21% pressure, +33% power
+10% rpm → +10% flow, +21% pressure, +33% power
K-style gutter: slope to the outlet, expansion joint on long runs, 11.5 mm of movement per 10 m.
K-style gutter: slope to the outlet, expansion joint on long runs, 11.5 mm of movement per 10 m.
Parallel line in 5 steps, radial line in 4, triangulation in 4 — side by side.
Parallel line in 5 steps, radial line in 4, triangulation in 4 — side by side.
Stretchout, areas, De, Pythagoras, gores, arc angle, Q = A × V, VP and fan laws on one sheet.
Stretchout, areas, De, Pythagoras, gores, arc angle, Q = A × V, VP and fan laws on one sheet.

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 62 topics.

The Problem Isn't You. It's How It Was Explained to You.

You're at the bench with a square-to-round, square on the bottom and round on top, and the pattern has to come out on paper first. You've built plenty of these, but the true lengths won't line up.

Your school notes explain triangulation in paragraphs: plan view, elevation and true length all in one block. Nobody showed you the steps in order.

Why an offset square-to-round needs a true length diagram for each quarter.

In the book, the centred square-to-round is a single page: the circle divided in 12, four corner sections of 3 triangles each, four flat triangles, and the seam at the centre of a flat side. You see the whole fitting before you read a word.

Same with gore angles, the Pittsburgh lock, equivalent round diameter, the fan laws and flashing: each one has its own page.

You lay it out, number the lines and cut. No going back to the binder to check what comes next.

COMPARE FOR YOURSELF

The Same Topic, Two Ways to Study It

THIS
  • The manual: line after line of text
  • Elbow layouts explained only in words
  • You walk into the exam still unsure
In the fabrication of a multi-piece round elbow, the total angle of turn must be distributed among the gores in such a manner that each of the two end sections receives one half of the angle assigned to each intermediate section. Accordingly, the angle of a full gore is obtained by dividing the total angle by the number of pieces less one. For a 90-degree elbow in five pieces, this yields three full gores of 22.5 degrees and two end gores of 11.25 degrees, to be verified before layout.
FOR THIS
  • Every gore of the elbow in one drawing
  • The rule and the angles in one box
  • You see it and you get it
Gore = angle ÷ (pieces − 1): 90° in 5 pieces = 3 × 22½° + 2 × 11¼°.
CONTENTS

Take a Look at the 9 Parts and 62 Topics

The exam and the basics, trade math, parallel line, radial line and triangulation, seams and joints, air flow and duct systems, architectural work and drawings, and a final review: 66 pages, all illustrated

IThe Exam and the Basics · pp. 5-9
  1. How the Red Seal exam is built
  2. Reading a question the way the exam writes it
  3. Metric and imperial on the same bench
  4. Gauge vs. thickness
  5. Sheet metals and their coatings
IITrade Math · pp. 10-17
  1. Circumference and stretchout
  2. Areas of rectangles and circles
  3. Equivalent round diameter
  4. Pythagoras for offsets
  5. The 45° offset multiplier
  6. Slope, pitch and percent grade
  7. Weight of sheet and duct
  8. Gore angles for round elbows
IIIParallel Line Development · pp. 18-24
  1. The three methods, side by side
  2. Parallel line in 5 numbered steps
  3. Two-piece 90° round elbow
  4. Five-piece round elbow
  5. Round pipe cut at an angle
  6. Tee: round branch on round main
  7. Rectangular mitred elbow
IVRadial Line Development · pp. 25-29
  1. Radial line in 4 numbered steps
  2. Full cone and its arc angle
  3. Frustum: concentric reducer
  4. Cone cut by an inclined plane
  5. Square pyramid hood
VTriangulation · pp. 30-36
  1. True length: the core idea
  2. The true length diagram
  3. Square-to-round, centred
  4. Square-to-round, offset
  5. Rectangular-to-rectangular transition
  6. Rectangular-to-round with a different shape ratio
  7. Y-branch (breeches)
VISeams, Joints and Fabrication · pp. 37-45
  1. Seam allowances in one table
  2. Grooved seam in cross-section
  3. Pittsburgh lock
  4. Snap lock and button punch
  5. Transverse joints: drive slip and S-slip
  6. Flanged connectors and corners
  7. Edges: hems and wired edges
  8. Fasteners and joining
  9. Duct sealing classes
VIIAir Flow and Duct Systems · pp. 46-56
  1. Air flow: Q = A × V
  2. Static, velocity and total pressure
  3. Pressure classes for duct construction
  4. The fan laws
  5. Duct sizing by equal friction
  6. Fittings and turning vanes
  7. Balancing and volume dampers
  8. Fire dampers and their installation
  9. Hangers and supports
  10. Insulation, liner and vapour barrier
  11. Kitchen exhaust grease duct
VIIIArchitectural Work, Drawings and Safety · pp. 57-61
  1. Flashing and counterflashing
  2. Gutters and downspouts
  3. Standing seam and roof panels
  4. Reading shop and mechanical drawings
  5. Safety on the job
IXFinal Review · pp. 62-66
  1. Pattern steps on one page
  2. Formula sheet
  3. Most common mistakes, drawn
  4. Question types that come up most
  5. Last two weeks before the exam

One Page, One Topic, All Clear

Think of it this way:

The exam gives you a 90° round elbow in five pieces and asks for the end gore. Or the foreman needs it cut before lunch. You need the angle now, not after digging through a binder.

You open the gore angles page and see the elbow drawn piece by piece: three full gores of 22½°, two end gores of 11¼°, and the rule in a box, angle ÷ (pieces − 1). The number comes straight off the drawing.

+10% rpm → +10% flow, +21% pressure, +33% power

Same with the square-to-round, the Pittsburgh lock, the fan laws, equivalent round diameter, and flashing and counterflashing: each one on its own page.

Sheet Metal Worker Exam Illustrated is 66 illustrated pages in 9 parts, with the pattern steps, a formula sheet and the most common mistakes drawn at the end.

What you see drawn, you don't have to memorize.

What's Inside Sheet Metal Worker Exam Illustrated:

Ipp. 5-9

The Exam and the Basics

How the Red Seal exam is built, reading a question the way it's written, metric and imperial on the same bench, gauge vs. thickness, sheet metals and coatings

IIpp. 10-17

Trade Math

Circumference and stretchout, areas, equivalent round diameter, Pythagoras and the 45° offset, slope and grade, sheet and duct weight, gore angles

IIIpp. 18-24

Parallel Line Development

The three methods side by side, parallel line in 5 steps, round elbows in two and five pieces, pipe cut at an angle, round tee, rectangular mitred elbow

IVpp. 25-29

Radial Line Development

Radial line in 4 steps, the full cone and its arc angle, the concentric reducer, a cone cut on an incline, the square pyramid hood

Vpp. 30-36

Triangulation

True length and its diagram, square-to-round centred and offset, rectangular transitions, rectangular-to-round, the Y-branch

VIpp. 37-45

Seams, Joints and Fabrication

Seam allowances in one table, grooved seam, Pittsburgh lock, snap lock and button punch, drive slip and S-slip, flanged connectors, hems, fasteners, sealing classes

VIIpp. 46-56

Air Flow and Duct Systems

Q = A × V, static, velocity and total pressure, pressure classes, fan laws, equal friction sizing, turning vanes, balancing and fire dampers, hangers, insulation, grease duct

VIIIpp. 57-61

Architectural Work, Drawings and Safety

Flashing and counterflashing, gutters and downspouts, standing seam roofs, reading shop and mechanical drawings, safety on the job

IXpp. 62-66

Final Review

Final review: the pattern steps and the formula sheet on one page each, the most common mistakes drawn, the question types to practise, and a plan for the last two weeks

At the end of the book: Pattern steps and every formula on one page each, the most common mistakes drawn, and a plan for the last two weeks.

Plus: 2 Free Books

Sheet Metal Exam-Style Practice Questions

BONUS 1: «Sheet Metal Exam-Style Practice Questions»

Value on its own: US$ 17.90

Practise with multiple-choice questions written like the exam, each with the answer and the page to go back to.

The 15 Most Common Sheet Metal Mistakes

BONUS 2: «The 15 Most Common Sheet Metal Mistakes»

Value on its own: US$ 14.90

See each frequent mistake next to the correct version, drawn before and after, so you catch it on the bench and on the exam.

Sheet Metal Worker Exam Illustrated with 2 Free Books

  • Sheet Metal Worker Exam Illustrated: 66 illustrated pagesUS$ 63
  • BONUS 1: Sheet Metal Exam-Style Practice QuestionsUS$ 17.90
  • BONUS 2: The 15 Most Common Sheet Metal MistakesUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT SHEET METAL WORKER EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Sheet Metal Worker Exam Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're in your last apprenticeship level

You're in your last apprenticeship level

Every block of school gets its page: the pattern in numbered steps and the math as a worked example in metric, so you study it in the same order you'll be asked.

Your exam date is set

Your exam date is set

The final review puts the pattern steps, the formula sheet and the most common mistakes on a few pages, so you can go over everything in the last two weeks.

You've been in the trade for years

You've been in the trade for years

You already know the work. The book shows it the way the exam words it, from gauge vs. thickness to the fan laws, with nothing aimed at beginners.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT SHEET METAL WORKER EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Sheet Metal Worker Exam Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've been in the trade for years and I'm challenging the exam?

Yes. It isn't a beginner's book: it follows the topics of the exam in order, so you can match what you do on the job with the way the questions are written.

Where does the content come from?

It's checked against the Red Seal Occupational Standard for Sheet Metal Worker and the current exam breakdown, the National Building Code of Canada, the applicable CSA and ULC standards and the duct construction standards used on Canadian specs. It's written for Canada, not a US book: the interprovincial exam is the same across the participating provinces and territories, so it works wherever you write it. Metric units, with imperial where the trade still uses it.

Is it official material?

No. It's an independent study book. It isn't affiliated with or endorsed by the Red Seal Program or any provincial or territorial apprenticeship authority, and it doesn't give you a certificate: your certification is issued by your provincial or territorial apprenticeship authority.

Does it replace my apprenticeship training or technical school?

No. It's a review book to go with your training, your time on the job and the codes that apply to your work. It doesn't repeat your school manual: it takes the same topics and gives each one its own page, drawn, with the steps in order.

Are the practice questions the ones on the exam?

No. They're written for this book, in the style of the exam, each with the answer and the page to go back to.

How do I get it?

The book and the 2 bonus books come as a PDF to the email you enter at checkout. You can read it on your phone or print the pages you want for the shop.

Do I have to pay every month?

No. It's a one-time payment.

Can I have it on paper?

Yes. The PDF is printable, so you can print the whole book or just the pages you want in the shop.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading notes that don't stick.

See the square-to-round drawn once and you're set.

You walk into the exam knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT SHEET METAL WORKER EXAM ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.